Siding cost in Portland, Oregon depends on the kind of job first. A repair is priced per visit or per patch; a replacement is priced by how much wall there is, which material goes on, and what turns up once the old siding comes off. The table on this page gathers published figures for both, each labeled with its source, whether it is a Portland, regional or national number, and the date it was last checked. Treat them as reference points for reading a quote, not as a quote.
To price your own house, request a siding quote and include the siding material, which walls are affected and roughly when the house was built, the same factors the figures below turn on. We’ll follow up about your project.
What does siding repair cost in Portland?
Repair is priced as a job, not by the square foot of house. Angi’s Portland siding repair guide, checked September 27, 2026, puts a typical repair visit at $903 to $2,835, and fiber cement repair at $3 to $11 per sq ft repaired, Portland. Those figures describe a repair that stays within the visit. Four things push a repair past them:
- A minimum charge. Ask whether the quote carries one. Getting ladders or a lift and a crew to the house takes much the same time for one board as for several, so a single-board repair is not priced as a small slice of a larger job.
- Matching an old profile. Cedar bevel, hardboard and older fiber cement patterns are not always still made. Finding, milling or salvaging a match takes time; failing that, a whole wall may be re-sided so it reads as one surface.
- What is behind the board. Soft sheathing or framing under the damaged area is repaired before new siding goes back, and nobody can price it until the board is off. Dry rot repair is the common case on Portland houses.
- Paint. A new board is primed and painted, and touching up one board on a faded wall rarely matches; some repairs end up painting the whole wall.
For what a repair visit should include, see siding repair.
How siding is priced: wall area, not floor area
Replacement figures are quoted per square foot of wall, or per square (100 square feet of wall). The square footage on a listing is floor area, which does not tell you how much siding a house carries: a two-storey house of the same floor area has far more wall than a ranch, and gables, bays and dormers add more. That is why this page gives no “2,000 square foot house” total.
To use the ranges, start from the wall area: the contractor’s measured figure, or the length of each wall times its height, less large openings. Worked through for every 1,000 square feet of wall, the ranges come to:
- Fiber cement, Angi Portland: $9,000 to $16,000
- Engineered wood such as LP SmartSide, national: $7,000 to $12,000
- Cedar, national: $6,000 to $16,000
- Vinyl, national: $3,000 to $12,000
- Tear-off and disposal of the old siding, national: $700 to $2,000
Sheathing repair, trim, soffits, paint and any lead-safe or asbestos work are on top of those lines. The asbestos siding guide explains the Oregon survey step for houses built before 2004.
How to read the ranges
- Per-square-foot figures are installed prices for the siding material, per square foot of wall. Multiply by your wall area (not your floor area) for a rough scale, then add the lines they leave out: tear-off, sheathing repair, trim and paint.
- Per-job regional averages come from the Remodeling 2025 Cost vs. Value Report and describe one house size, 1,250 square feet of siding including trim. Portland is not reported separately; the figures average the report’s Pacific region markets. Whether a re-side adds resale value, and whether it changes Oregon property taxes, is covered in does new siding increase home value.
- Repair figures for Portland describe a typical repair visit, not a job where rot has reached the sheathing.
What do siding materials cost to install?
The table below compares fiber cement, vinyl, cedar, engineered wood and T1-11. Fiber cement and cedar sit higher per square foot than vinyl and T1-11; engineered wood sits in between. Fiber cement’s price buys a board that does not rot; cedar’s buys real wood that can be repaired board by board; vinyl’s lower price comes with sensitivity to heat and installation. The engineered wood row is the one to use for LP SmartSide; the LP SmartSide guide covers how it differs from fiber cement and from the LP siding of the 1990s. For Hardie board specifically, see Hardie siding cost in Portland on the fiber cement page, and for how long each material lasts before it is priced again, the siding lifespan guide.
Repair or replacement: which budget are you in?
A siding repair on one wall usually lands within the Portland repair range in the table. Full replacement is a different order of cost, which is why it is worth being sure the siding has actually failed before pricing it. The common reasons it has are swollen hardboard, failing T1-11 and rot from water behind the siding.
Getting comparable quotes
Quotes only compare when they cover the same scope. Ask each contractor to list:
- tear-off and disposal, and lead-safe work if the house predates 1978;
- a unit price for sheathing replacement;
- the house wrap, flashing and drainage gap they will install;
- trim, soffit and fascia scope and material;
- paint or finish, and how many coats;
- who handles any permit or historic review.
Oregon requires a written contract for residential work over two thousand dollars, showing the contractor’s CCB license number. The guide to comparing siding quotes covers the rest of what Oregon requires at signing, and how to line quotes up side by side. The siding services page sets out what each kind of job should include, and the common siding problems page helps you describe what you are seeing when you ask for a quote. About Portland Siding Pros explains where the figures on this page come from and what the site does not do.
Last updated