Most of Tigard’s houses were built after the city incorporated in 1961, and the biggest share of them in the 1970s and 1980s. Those two decades account for about 40 percent of Tigard’s homes today (Census ACS 2020-2024), and they are the houses now old enough for their first siding to give out. Tigard also words the state’s siding permit exemption in its own way, reviews exterior changes to its historic overlay properties, and shares its two ZIP codes with unincorporated neighborhoods and two small cities that get their permits elsewhere.
For a house in Tigard’s ZIP codes, 97223 and 97224, request a siding quote and note whether the address is inside the city or in one of the unincorporated neighborhoods that share those ZIP codes, and roughly when the house was built.
Tigard’s houses by decade
Wilson M. Tigard, whose family gave the city its name, arrived in 1852, and pioneers took up donation land claims here through the 1850s (City of Tigard history). Little of that era survives in the housing count. The Census Bureau’s 2020-2024 estimates put the median Tigard home at 1988, and the building curve looks like this:
| Decade built | Share of Tigard homes |
|---|---|
| 1959 or earlier | about 5% |
| 1960s | about 9% |
| 1970s | about 21% |
| 1980s | about 19% |
| 1990s | about 18% |
| 2000s | about 12% |
| 2010 or later | about 17% |
The 1970s are the single largest decade, but Tigard never stopped building after them; every decade since has added more than a tenth of today’s homes. About 57 percent of Tigard’s housing units are single-family detached houses and another 9 percent are attached single-family homes such as townhouses, where a re-side has to stop cleanly at a shared wall. About 62 percent of households own their home.
What the walls on those houses are likely to be
Housing age narrows the possibilities without settling them. Two dates are documented. Hardboard lap siding, much of it sold as Masonite, was covered by a class settlement for boards installed from 1980 to January 1998. LP’s Inner-Seal OSB siding was the subject of a class action in federal court in Oregon covering boards installed before 1996. Both closed to claims years ago. Tigard’s 1980s and 1990s houses, more than a third of the city, fall inside those windows, and a house re-sided in those years may too.
The 1970s houses predate both settlements. On those, plywood panel siding, cedar and early hardboard are all possible, and only a look at a cut edge settles it. The hardboard siding failure and T1-11 damage pages explain how each one fails and how to tell them apart.
Houses built since 2000, about 29 percent of Tigard, are clear of both settlement windows. On a newer house the first places to check are the details rather than the boards: roof-to-wall corners without a kickout flashing, window heads and the bottom course where it meets a patio or planting bed. Those are the usual entry points for water behind siding.
Tigard ZIP codes, other permit desks
Tigard’s two ZIP codes reach well past the city limit. In the Census Bureau’s 2020 relationship files, the City of Tigard covers about 69 percent of the land in ZIP code area 97223 and about 53 percent in 97224. The rest belongs to places with their own permit arrangements:
- Metzger, north of the city, is unincorporated. Washington County’s Metzger-Progress community plan places it north of Tigard and east of Beaverton, and says most of the area is detached single-family houses. It is also older than Tigard: a median home from 1975, with about 63 percent built before 1980 (ACS 2020-2024, Metzger census-designated place).
- Bull Mountain, west of the city, is the reverse. The county’s Bull Mountain community plan records a planning area that annexations have been cutting back since 1983, and its history table lists 16 annexations to Tigard between 1994 and 2006. The unincorporated remainder has a median home from 1996, and about 44 percent of its homes date from the 1990s.
- Garden Home-Whitford and Raleigh Hills, both unincorporated, also reach into 97223.
- King City and Durham, in 97224, are small cities of their own. King City takes building permit applications through the state’s ePermitting system, and Durham takes them at City Hall and contracts with the City of Tualatin for inspections.
The state’s building agency says unincorporated areas are served by the county, and Washington County Building Services handles unincorporated Washington County. A Metzger or Bull Mountain house therefore runs under the state’s exemption as the County applies it, not under Tigard’s wording below. A mailing address will not tell you which side of the line a house is on, so settle that with a call before comparing rules or quotes.
The City of Tigard’s siding permit rule
Tigard’s building division publishes its own list of work that needs no building permit. For siding, it says no building permit is required if the replacement is like kind and not required to be fire resistive, and for all other types it asks owners to call the Building Division about lateral bracing requirements.
The state residential code is broader: its exemption covers replacement or repair of any siding not required to be fire-resistance rated (ORSC R105.2). The difference lands on the most common Tigard jobs. Replacing swollen hardboard with fiber cement is not like kind, and neither is stripping plywood panels and going to lap siding. Panel siding is sometimes the only sheathing a wall has, which is where bracing comes in. If the job changes material, ask the contractor to call the Building Division before the quote is final and to note the answer on the quote.
The same City page adds:
- Windows and doors: replacing them needs no building permit where no structural member is changed.
- Zoning still applies: an exemption from a building permit does not exempt a project from the planning rules in Title 18 of the Tigard Municipal Code, and the City asks owners to check setbacks and zoning with its planning division.
- Associations: the City does not enforce homeowners association covenants and restrictions, and tells owners in an association to confirm the project does not break its rules.
A wall has to be fire-resistive mainly when it stands close to a property line, which the state residential code puts at less than 3 feet. On a Tigard lot with a tight side yard, re-siding that wall is permit work whatever the material. And if the re-side means moving an exterior light or outlet, Tigard’s Building Division issues that electrical permit too; unlike several of its neighbors, the City handles its own trade permits.
Tigard’s historic overlay
Tigard protects historic buildings through a Historic Resource Overlay zone, set out in Chapter 18.755 of its development code. Exterior alterations to any structure in the overlay without approval are prohibited. The code treats any change in design or other exterior treatment as an alteration, except painting. Its carve-out for ordinary maintenance and repair is narrow: work that changes nothing about a feature’s design, material or appearance, and that the building official certifies is needed for safety. An alteration goes through a Type II review, and one of the approval criteria is how well the proposed materials, texture and color suit the existing building. Every approval carries a condition letting the Washington County Museum record the building and collect artifacts worth keeping.
The City lists ten historic and cultural sites, and owners can apply to add a property to the overlay. The best known is the John Tigard House, built around 1880 and moved in 1979 from Pacific Highway and Gaarde Street to SW Canterbury Lane at 103rd Avenue; it was the first Tigard property listed in the National Register of Historic Places. If a house is on the City’s list, talk to the planning division before any siding work, like-for-like included. Historic wood siding repair covers the ways of keeping original boards.
Siding repair in Tigard
Most calls start with a handful of bad boards. What decides whether a repair lasts is what sits behind them:
- Soft wood at the bottom course, under window sills or where a deck ledger meets the wall is usually dry rot. Probing tells you whether it stops at the board or has reached the sheathing, which is the line between a morning’s work and a wall section.
- Stains below a roof-to-wall corner point to a missing kickout flashing sending roof water into the wall.
- Swollen lower edges on lap boards are the hardboard and OSB failure described above. A few boards on one wall can be swapped; the same swelling on every elevation is a replacement conversation.
- Discontinued profiles: many 1980s hardboard and OSB patterns are no longer made, so replacement boards are often fiber cement or engineered wood cut to the same exposure and painted in.
Siding repair explains the repair options and when patching stops making sense. Because Tigard’s permit note speaks of like-kind replacement, a patch in a different material is worth mentioning to the Building Division when it covers more than a few boards.
Siding replacement and material choices
When the failure is on every wall, siding replacement lets the contractor open the wall: replace soft sheathing, put on a continuous water-resistive barrier, flash every window and door, and add a drainage gap where it is needed. The cladding choice in Tigard is the same as across the metro:
- Fiber cement, lap or panel, does not swell like hardboard; it is heavier and thicker, so window and door casings may need building out.
- Engineered wood lap (LP SmartSide and similar), the successor to the old OSB lap products, must be sealed and installed exactly as its maker specifies.
- Vinyl needs no paint but must be hung loose so it can move with heat.
- Cedar is real wood and asks for regular stain or paint.
Any of these on a house that had hardboard or panels is a change of material, which is exactly the case Tigard’s permit note sends to the Building Division. Build that call into the schedule rather than finding out mid-job.
What to settle before a Tigard quote
- City or county? Confirm the house is inside Tigard’s limits, or in Metzger, Bull Mountain, King City or Durham.
- Like kind or a new material? In Tigard, that decides whether the job needs a word with the Building Division.
- Any wall within 3 feet of a property line? That wall is permit work.
- Built before 1978? Then the contractor needs the CCB’s Lead-Based Paint Renovation license if the job disturbs 20 square feet or more of exterior paint.
- Historic overlay? If the house is one of the City’s listed sites, review comes before scheduling.
- Trees? Tigard needs no permit to remove a tree on a single-family lot unless it is a street tree, a heritage tree, planted through the Urban Forestry Fund, or native and in sensitive lands (City tree permits).
- Homeowners association? Check its rules on materials and colors yourself; the City will not.
What siding work costs around Tigard
Nobody publishes a Tigard price. The nearest published numbers are Angi’s cost guides for the Portland market, last checked September 27, 2026: a single siding repair job at $903 to $2,835. Fiber cement, supplied and installed, comes to $9 to $16 a square foot of wall area. Engineered wood lap and vinyl have only national ranges, $7 to $12 (HomeGuide) and $3 to $12 (Fixr) per square foot installed.
Because a Tigard hardboard re-side is a change of material, two lines deserve a look on any quote: tear-off and haul-away, which HomeGuide puts at $70 to $200 for every 100 square feet of wall nationally, and a unit price for any sheathing replaced once the old boards are off. The siding cost page shows the source behind each figure, and comparing siding quotes in Oregon covers the rest of a bid.
Nearby: Tualatin, Lake Oswego, Beaverton and Portland.
Last updated