Re-siding

Insulated Siding in Portland: Foam, R-Value & Oregon Code

Insulated vinyl, rigid foam under new siding and dense-pack walls on a Portland re-side: tested R-values, Oregon code, Energy Trust and moisture.

Insulated siding usually means foam-backed vinyl: ordinary vinyl panels with a rigid foam backer bonded on, tested at R-2.0 or more. It is one of three ways a Portland re-side can add insulation. The others are rigid foam boards under any siding, and dense-packed insulation blown into the stud cavities while the wall is open. Each changes the wall in different ways.

This guide explains what each one adds, what Oregon’s code says about insulation when a house is re-sided, what Energy Trust of Oregon pays for, and how to keep an insulated wall dry in a wet climate. Oregon’s 2026 residential code took effect October 1, 2026, and building departments must also accept work designed to the 2023 edition until March 31, 2027 (OAR 918-480-0005); the sections cited are the 2023 edition’s. Every source was read on October 10, 2026.

What is insulated vinyl siding?

It is vinyl siding with foam plastic insulation built into it. ASTM’s specification for the product, D7793, sets that definition and requires a tested thermal value of R-2.0 or greater, alongside the impact, wind-load and dimensional tests ordinary vinyl has to pass. The Department of Energy’s Building America Solution Center describes a permanently attached rigid foam backing, usually expanded polystyrene, and puts most products at about R-2.0 to R-2.8 (BASC).

Three things are worth knowing before comparing products:

  • Look for the label and the tested number. The Vinyl Siding Institute certifies insulated vinyl to D7793 and lists certified products; its installation manual tells buyers to look for the certification label on the box, and the industry association says certified packaging shows the product’s R-value.
  • R-value claims have to be tested. The FTC’s R-value rule covers products that are not insulation but are sold partly to save energy by slowing heat flow. An R-value claimed for one must come from a test the rule lists, such as the ASTM C1363 hot box, and must reflect the results (16 CFR 460.22). The rule does not name siding, but insulated vinyl sold on its R-value fits the description. An “up to” figure covers a whole product line, not the profile on your wall.
  • It is a thin layer. About R-2 across the whole face of the wall reduces heat loss through the studs, which cavity insulation does not cover. It does not replace insulation in the cavities.

Fastening changes slightly. The VSI manual has installers butt the foam tight at the panel overlaps, nail in the center of the slots, and use nails long enough to reach the framing, or framing plus nailable sheathing, through the extra thickness. Vinyl of any kind needs sheathing behind it and a continuous water-resistive barrier.

Why is there foam behind my siding?

Usually it is a backer bonded to insulated vinyl panels, a thin fan-fold foam underlayment, or rigid foam sheathing fastened over the wall. The VSI manual’s fastening diagrams show fan-fold foam where vinyl goes over old wood lap, so finding it hints that the original siding may still be underneath. Rigid sheathing means every fastener had to pass through it to reach the framing.

Foam under a hard, textured coating is EIFS, a different cladding with its own history and rules; the stucco to siding guide covers it.

Three ways to add insulation during a re-side

A re-side is the one time the outside of the wall is open, which makes it the easiest time to add insulation from outside. The three options can be combined.

Insulated vinyl Rigid foam under the siding Dense-pack in the stud cavities
What it is Foam backer bonded to each vinyl panel Boards of foam insulation fastened over the sheathing, with any siding on top Loose-fill insulation blown tight into empty or part-filled cavities
What it adds R-2.0 minimum (ASTM D7793); most products about R-2.0 to R-2.8 (BASC) Depends on the board and its thickness Fills the cavity; the R-value depends on the cavity depth and the product
Siding choice Vinyl only Any siding whose maker allows it over foam Any
What changes on the wall A little extra thickness and longer nails Wall gets thicker: windows, doors, trim, fasteners, and possibly furring Holes through the sheathing, patched before the house wrap goes on
Who does it Siding contractor Siding contractor Insulation contractor

The comparison draws on the sources cited in each section below. Oregon’s own energy chapter is a useful yardstick: a new house’s prescriptive walls are R-21 in the cavities, and one of the code’s optional upgrade measures is R-21 with R-5 of continuous insulation outside it (2023 ORSC Tables N1101.1(1) and N1101.1(2)). Nothing requires an existing house to reach those numbers.

What rigid foam under new siding changes

Continuous foam outside the sheathing covers the studs as well as the cavities between them, which is why building scientists favour it. It also makes every wall thicker, and the details at its edges decide whether the job works.

Where the water-resistive barrier goes. DOE’s guide to rigid foam on existing walls describes two positions. Over the existing sheathing, with the foam outside it, the windows stay where they are in the framing. On the outer face of the foam, the foam itself becomes the drainage plane, with taped seams and a foil-faced polyiso or extruded polystyrene board at least an inch thick, and the windows move out into the foam layer. Either way, the guide starts by stripping the old cladding and trim and removing windows and doors as needed so the openings can be flashed properly.

Windows and doors. A thicker wall means the openings have to be built out so trim, sills and flashing reach the new face. In one retrofit DOE photographed, lap siding went over four inches of foam and the windows were framed out with plywood to the depth of the foam plus 1x4 furring (BASC). Oregon’s code requires window and door flashing to extend to the surface of the exterior finish (R703.4), so the flashing has to be planned for the new depth, not the old one. Swapping a window into the same size opening needs no Portland building permit, but widening or shrinking an opening does (PP&D).

Fasteners. The code makes the siding maker’s instructions, including any limits on installing over foam, the first rule (R703.15). Nails or screws through foam must be long enough to pass through it and still reach the framing to the required depth (R703.3.4), and the code’s table for nailing straight through foam shows how quickly the allowance shrinks as the cladding gets heavier. For a 0.113-inch nail every 6 inches into studs 16 inches apart, the table allows up to 2 inches of foam under a cladding weighing 3 pounds per square foot, 1.45 inches at 11 pounds, and calls for a design at 25 (Table R703.15.1). Past those limits the siding goes onto furring strips fastened through the foam into the structure, which also gives the wall a drainage gap.

Vinyl over foam. Vinyl or insulated vinyl over foam with no structural sheathing behind it needs a wind-load rating suited to the site; over plywood or OSB the normal vinyl rules apply (R703.11.2).

Trim and edges. J-channel, corner posts and casing all have to suit the new thickness, and the BASC guide puts J-channel on only after the windows are flashed. On a partial re-side, where foam stops and an old wall continues, ask how the two planes will meet.

Filling empty walls while the sheathing is open

If the walls have little or nothing in the cavities, insulation blown in from outside often does more than anything layered over them. DOE’s guide to blown insulation in existing walls calls a re-side the ideal time to do it from the exterior. The insulation contractor drills the sheathing, fills each cavity to the density the product’s maker specifies, and checks the result, often with an infrared camera. What the guide asks for along the way:

  1. Check the wiring first. Insulation must not be packed around old knob-and-tube wiring. That check belongs to an electrician, before the cavities are filled.
  2. Block balloon-framed walls. In a wall whose studs run past the floors, the cavities need blocking at the top and bottom or the insulation keeps falling.
  3. Make the drainage plane whole again. Every hole through the sheathing, and any old building paper the work disturbs, is patched or the barrier replaced before the new house wrap and siding go on. The siding contractor should know the holes are coming.
  4. Follow lead-safe rules on older houses; in Oregon, disturbing 20 square feet or more of exterior paint on a house built before 1978 takes a contractor with the CCB’s lead-based paint renovation license.

On a house built before 2004, Oregon DEQ also requires an accredited asbestos survey before the re-side, covering anything the work will disturb; the asbestos siding guide sets out the rule.

Does Oregon’s code require insulation when you re-side?

Not in so many words. Oregon writes its own residential energy chapter, and its rule for existing houses is about alterations that affect the energy-regulated parts of the house: those parts have to meet the chapter. Its exception lets the existing-building minimums be met “to the maximum extent technically practical”, naming limits such as the depth of the cavity (2023 ORSC N1101.2.1). For walls, that table sets U-0.083, equivalent to R-15 (Table N1101.2). The chapter does not mention siding, and it contains no definition of insulated siding or continuous insulation, so nothing in it says whether foam-backed vinyl counts toward a requirement.

In practice, Portland Permitting & Development lists replacing or repairing siding that is not required to be fire-resistant, and installing insulation in an existing home, among the jobs that need no building permit (PP&D). Work without a permit still has to meet the codes; it simply is not inspected. Whether a particular re-side “affects” the wall’s insulation enough to bring in N1101.2.1 is a question for the building department, not this guide. Changing the size of a window or door opening does need a permit, and so can a wall close to a property line; the Portland permits page explains that case, and the review historic and conservation districts apply to a change of siding material such as vinyl.

Keeping an insulated wall dry in Portland’s climate

Insulation changes how a wall dries, and in a climate this wet that matters more than the R-value. Four points from the code and the building-science sources:

  • Vapor retarders. Oregon’s code asks for a Class II vapor retarder on the warm-in-winter side of framed walls, and allows the more permeable Class III where vented cladding sits over wood structural panels or continuous air-impermeable insulation is on the outside (2023 ORSC R318.1).
  • Do not trap the wall from both sides. DOE’s guides warn against foam-backed siding or exterior foam over a wall with polyethylene or vinyl wallpaper on the inside, which leaves the wall unable to dry either way, and against siding over any wall showing moisture problems until the cause is fixed (BASC).
  • Enough foam, or none. Building Science Corporation’s BSD-163 explains that foam outside the sheathing keeps the sheathing warmer, which reduces condensation from indoor air leaking into the wall, but that adding air-permeable insulation to the cavity raises the risk, and too thin a layer outside does not protect it. The ratio is a design question for the contractor, not a rule of thumb.
  • Leave a way out for water. Oregon’s code wants at least 1/8 inch of drainage space behind new siding, with listed exceptions (R703.1.1), and the water behind siding page shows what happens without it. Wood siding needs particular care: the Western Red Cedar Lumber Association’s caution about rigid foam behind cedar is on the cedar siding repair page.

Energy Trust incentives and tax credits

Energy Trust of Oregon’s insulation page listed these Oregon wall-insulation incentives on October 10, 2026:

Home Incentive
Owner-occupied single-family house 1.50 dollars per sq ft
Owner-occupied duplex to fourplex, or townhome 2.25 dollars per sq ft
Rental, single-family to fourplex 2.25 dollars per sq ft
Income-qualified through Savings Within Reach 2.25 dollars per sq ft

The conditions are the same in each row: the existing walls must be R-4 or less, and the work must bring them to R-11 or more or fill the accessible cavity. The house has to be heated mainly by fuel from PGE, Pacific Power, NW Natural, Cascade Natural Gas or Avista. For contractor-installed work, the application is due within 60 days of installation, must be signed by the installing contractor and show the starting and finished R-values and the square footage, and takes six to eight weeks to process. The page lists no incentive for insulated siding or exterior foam. Incentives change, so check the page, and with the insulation contractor, before the work is scheduled.

The federal Energy Efficient Home Improvement Credit no longer helps: the IRS says it applied to qualifying insulation placed in service from January 1, 2023 through the end of 2025 (IRS).

Who does what on an insulated re-side

Insulation is a related trade, and the jobs overlap at the sheathing. A typical split:

  • The siding contractor removes the old siding, repairs sheathing, installs any rigid foam, the water-resistive barrier, flashing, furring and trim, and the new siding, including insulated vinyl.
  • The insulation contractor blows the cavities while the wall is open and, for the Energy Trust incentive, signs the application. Energy Trust’s trade ally network lists contractors who work with its requirements.
  • An electrician checks for knob-and-tube or other wiring that rules out filling a cavity.
  • Accredited inspectors and licensed firms handle the asbestos survey on a pre-2004 house and lead-safe work on a pre-1978 one.

The order matters: tear-off, inspection and repair of the sheathing, wiring check, cavity fill, patching the sheathing, then the barrier, any foam, flashing and siding. Every contractor in that sequence needs an active Oregon Construction Contractors Board license, which the guide to comparing siding quotes shows how to check.

What it costs, and what to ask for in the quote

This site has no dated, sourced figure for insulated vinyl, rigid foam or blown cavity insulation, so it publishes none. Fixr’s national guide puts standard installed vinyl siding at $3 to $12 per square foot of siding, and the siding cost page lists the other materials and notes that insulated vinyl moves a job up the range.

Ask each contractor to price these as separate lines, so two quotes can be compared:

  1. the siding product by name, and its tested R-value if it is insulated vinyl;
  2. any rigid foam: type, thickness, and where the water-resistive barrier goes;
  3. window and door work: extension jambs or bucks, sills, flashing and trim for the new wall depth;
  4. fasteners and furring, and the maker’s instruction or code table they follow;
  5. cavity insulation by the insulation contractor, with its R-value and square footage for the Energy Trust application;
  6. sheathing repair, per sheet or per hour, and patching after the cavity fill.

For the rest of a full re-side, from tear-off to house wrap, see siding replacement.

To send a request describing the job, use the request page. Whoever does the siding or the insulation, check their license on the Oregon Construction Contractors Board’s license search before signing anything.

Start My Siding Quote

No cost and no obligation. Tell us about the house and the siding problem to get started.

Questions, answered

Common questions

Should I get insulated vinyl siding?

It suits a house that is getting vinyl anyway and has walls that are flat, sound and dry. The foam backing adds a modest, tested amount of insulation, R-2.0 at the least under its ASTM standard, and it stiffens the panel. It does not fill an empty stud cavity, and a federal guide warns against putting it over a wall with moisture problems. If the walls hold little or no insulation, filling the cavities usually matters more, and the open wall during a re-side is the moment to do it.

What is the R-value of insulated vinyl siding?

ASTM D7793, the standard for the product, requires a tested value of R-2.0 or more, and the Department of Energy's Building America guide puts most products at about R-2.0 to R-2.8. Certified products print their own figure on the box. Under the FTC's R-value rule, any R-value claimed for a product sold partly to save energy has to come from a test listed in the rule, so ask the contractor for the product's published figure rather than a sales estimate.

Why is there foam behind my siding?

It is usually one of three things. Insulated vinyl has a contoured foam backer bonded to each panel. Older vinyl jobs sometimes used a thin fan-fold foam underlayment over the old wall. And some houses have rigid foam sheathing, boards of insulation fastened over the wall before the siding went on. Foam with a hard, textured coating on its face is a different system, EIFS, which is stucco-like rather than siding.

What is the most important place to insulate a house?

Energy Trust of Oregon calls the attic the most important area to insulate properly, because warm air rises, and says wall and floor insulation also save energy and improve comfort. Its wall incentive is aimed at walls with very little insulation: existing walls must be R-4 or less. A re-side does not touch the attic, but it is the cheapest time to reach the walls.

Does Energy Trust of Oregon pay for wall insulation?

As of October 10, 2026, yes, for homes heated mainly by fuel from PGE, Pacific Power, NW Natural, Cascade Natural Gas or Avista. The Oregon rate for an owner-occupied single-family house is 1.50 dollars per square foot, where the existing walls are R-4 or less and are brought to R-11 or more or filled. The application is due within 60 days of installation and must be signed by the installing contractor. Incentives change, so check Energy Trust's page before the work is booked.

How much does it cost to install 1,000 square feet of vinyl siding?

Fixr's national guide puts installed vinyl at $3 to $12 per square foot of siding, which comes to $3,000 to $12,000 for 1,000 square feet. That figure is for standard vinyl. This site has no sourced figure for insulated vinyl, rigid foam or cavity insulation, so it publishes none; ask for each as its own line, with tear-off, house wrap, trim and window work priced separately.

A free siding quote request

Start My Siding Quote

No cost and no obligation. Tell us about the house and the siding problem to get started.

No cost to submit a request, and no obligation.