Dry Rot in Portland Homes: What It Is and Where It Hides
What dry rot really is, why Portland's wet winters feed it, ten places it starts on a house, and what it means for Oregon home sales, loans and insurance.
Published September 27, 2026Updated September 28, 2026
Most people meet dry rot with a screwdriver. You are scraping a windowsill before painting it, or pulling a dead plant away from the foundation, and the tip slides into the wood like it was pushing into cork. The paint looked fine. The board looked fine. It was not fine.
It tends to happen during spring cleanup or while prepping to paint in summer, and it raises the same three questions. What is this stuff? How did it get here, when the house has been painted? And how far does it go? This guide answers all three, then walks around the outside of a typical house to show where rot starts, and covers what it means if you are buying or selling a house in Oregon.
What is dry rot?
Dry rot is wood being eaten by a fungus. Not a mold sitting on the surface, but a decay fungus living inside the board, sending microscopic threads called hyphae through the wood cells and digesting the wood itself as food.
The name is misleading, and wood scientists say so. The USDA Forest Products Laboratory’s Wood Handbook, the Forest Service’s reference book on wood as a building material, calls the term incorrect, because wood must have water available for decay to happen at all. What people call dry rot is usually brown rot seen after the fact: the fungus did its work while the wood was wet, then the wood dried out over the summer and was left brown, shrunken, cracked across the grain into little cubes, and crumbly enough to crush between your fingers.
There are three kinds of wood decay in the Handbook, and on a Portland house you are most likely to see the first:
- Brown rot strips out the cellulose, the long fibers that give wood its strength. The wood darkens, shrinks and checks into cubes. Brown-rot fungi commonly attack softwoods such as Douglas-fir and cedar.
- White rot takes the lignin as well as the cellulose. The wood goes pale, keeps its shape and feels spongy rather than crumbly. You find it more often in hardwoods such as maple and oak.
- Soft rot is shallow, mostly affecting the outer surface, and the Handbook ranks it as generally less important.
There is also a small group of brown-rot fungi that can grow root-like strands and pipe moisture out of damp soil, wetting wood that would have stayed too dry to rot on its own. The Handbook says these are sometimes called dry-rot fungi, but prefers “water-conducting fungi”, because like every other decay fungus they must have water. For practical purposes, if you have rot, you have a water problem.
How and why dry rot happens
A decay fungus needs four things: spores to start from, water, air, and a temperature it can grow at. Take away any one and the rot stops.
Spores are a given. The Handbook calls the spores of decay fungi ubiquitous. A single fruiting body releases thousands, and wind and insects carry them everywhere. Every board on your house almost certainly has spores on it right now. You cannot keep them out, which is why every piece of advice about rot comes back to water.
Water is the switch. A spore only germinates on wood that is wet, and “wet” has a specific meaning here. Wood holds water in two ways: bound inside the cell walls, and free in the cell cavities. The point where the walls are full, called the fiber saturation point, averages about 30 percent moisture content. The Handbook says serious decay happens only above it. Wood that has been air-dried usually sits at 20 percent or less, which it describes as a reasonable margin of safety, and at that level decay already in the wood stops progressing.
What matters is how wood gets from 20 percent to 30. The Handbook’s answer is specific: only rain, condensation, or contact with wet ground will do it. The water vapor in humid air, by itself, cannot wet wood enough to support significant decay. So Portland’s damp winter air is not what rots houses. Liquid water getting into the wood, and staying there, is.
Air is the odd one. Wood can be too wet to rot. When it is completely waterlogged, there is not enough oxygen inside for typical decay fungi to grow, which is why the Handbook notes that foundation piles below the water table do not decay. That is little comfort for a house, where wood is almost never fully submerged, but it is a reminder that the fungus is a living thing with limits.
Temperature sets the pace. The typical decay fungus does best around 77°F. Per the Handbook, growth drags when the wood is colder than 50°F or hotter than 95°F, and at 35°F, or at 100°F, it all but halts. A cold, wet January slows rot down. A mild, wet October or April, with the wood still soaked from months of rain, is when it moves.
Why Portland gives rot a long season
In 1971, the researcher T.C. Scheffer published a way to score how hard a local climate is on outdoor wood that sits above the ground. It combines each month’s average temperature with its number of rainy days. The Forest Products Laboratory recalculated it in 2009 from 1971-2000 weather records, and sorts places into three groups on its map: below 35, from 35 to 65, and above 65.
Portland comes out at 52.4. That is in the middle band, and higher than Seattle-Tacoma at 49.9, Salem at 43.9 or Eugene at 40.8. Astoria, on the coast, is 69.2. The authors stress that the number cannot tell you how quickly rot will move through a given house, or when a particular wall will give out. What it does say is that a Portland house has a long stretch of the year when wet wood and mild temperatures overlap.
The rainfall shows why. At Portland International Airport, NOAA’s 1991-2020 climate normals average 36.92 inches of rain a year. November, December and January each bring over five inches; July and August manage roughly half an inch apiece. A board that gets soaked in November can stay above 30 percent until the dry months arrive.
Why paint does not stop it
This is the part that surprises most people. A well-painted house can still rot, and the reason is end grain.
Wood is a bundle of tubes running along the length of the board. Cut across it and you open the ends of those tubes. According to the Handbook’s chapter on finishing wood, liquid water enters wood 10 to 100 times faster through end grain than through the other faces. Sealing end grain is, in the Handbook’s words, probably the single most valuable improvement that can be made in standard construction practice.
Now think about where end grain sits on a house: every place a siding board butts into a corner board or window casing, the bottom of every piece of trim, the ends of porch boards, the foot of every porch column. Those joints move with the seasons, and the Handbook says coatings always fail eventually at joints, from movement, wear, fasteners, or even microbes. The USDA’s older homeowner bulletin, Wood Decay in Houses: How to Prevent and Control It (Home and Garden Bulletin 73, revised 1986), put it plainly: siding decay is most frequent in ends that are butted against trim, at windows, doors and corners.
Both sources agree on the bottom line. Paint is not a preservative. It keeps rain off the faces of the board, which helps a great deal, but it will not stop decay once water is in the wood. Back-priming siding, sealing every cut end during installation, and keeping the paint in good repair are what slow water down. Once it is in, only drying out stops the fungus.
One more wrinkle. Mildew and mold on siding do not do much damage themselves; the Handbook says they affect wood strength only slightly. But they make wood more absorbent, and that extra wettability can open the door to decay fungi on rain-wetted wood. A green north wall is not rotting because it is green, but it is a wall that stays wet, and that is worth paying attention to.
How bad is it? Strength goes first
Rot is worse than it looks, for two reasons.
First, the strength goes early. The Handbook reports lab tests in which wood that had lost a tenth of its weight to fungus had, in most cases, already lost more than half its strength, and at that point you would have needed a microscope to see the decay. Its takeaway: if you can see rot, assume the wood is badly weakened. Brown rot, the common kind here, weakens wood faster in its early stages than white rot.
Second, it often starts inside. The finishing chapter warns that decay often occurs in the center of a board while the surface appears sound. A windowsill can have a firm painted skin over a soft core, which is why the probe test matters more than looks.
For trim, that is an annoyance. For a porch post, a deck ledger or the sill plate the house sits on, it is a safety issue.
Ten places dry rot starts on a Portland house
The pattern is always the same: a spot where water lands, an opening for it to get into end grain or behind a surface, and not enough sun or air to dry it out again. Here is where that happens, starting with the walls and moving out to the porch, the garage and the crawlspace. The Census Bureau’s American Community Survey (2020-2024) puts Portland’s median year built at 1966, with 26.8 percent of the city’s housing units built in 1939 or earlier, so the typical house here has been through about sixty rainy seasons, and many have been through ninety or more.
1. The bottom course of siding
The lowest board on the wall takes splash-back from every storm, plus water wicking up from soil and mulch. The Wood Handbook recommends at least 6 inches between soil and siding and 8 inches between soil and framing, and the USDA bulletin says the lowest board should be 6 inches or more above the soil for greatest safety. Oregon’s residential code builds the same numbers in: the 2023 Oregon Residential Specialty Code, in section R317.1, requires naturally durable or preservative-treated wood for siding, sheathing and wall framing closer than 6 inches to the ground, or closer than 2 inches to concrete steps, porch slabs and patios. Decades of new bark dust tend to erase that clearance a little at a time. On grooved plywood panel siding, the same splash-back soaks the panel’s raw bottom edge, which is where T1-11 siding starts to come apart.
2. Siding ends at corners and trim
As above, this is where the end grain is. Look closely at the last few inches of each lap board where it meets a corner board or window casing. Dark paint, open caulk, or a board end that has swollen proud of its neighbors are early signs.
3. Window sills and the bottom of the sash
National Park Service Preservation Brief 9 lists the sill, the joint between the sill and the side jamb, the corners of the bottom rail and the muntin joints as the typical places water collects on a wood window. Rain runs down the glass, sits on the bottom rail and the sill, and works into the joints. The same brief notes that pressing a probe into a sill can force it through a sound-looking skin and deep into decayed wood underneath.
4. Below a roof-to-wall corner
Wherever a lower roof ends against a wall, a garage roof against the house, say, or a porch roof against a second story, roof water pours down the corner. Oregon’s code (R703.4) requires kickout flashing at those intersections to throw the water into the gutter. Without it, the Department of Energy’s Building America Solution Center warns, the water can rot out the window trim below, and newer claddings such as fiber cement, vinyl and brick veneer can mask the evidence for years. The Handbook also calls for a 2-inch gap between the end grain of siding and the roof surface below it, so the boards are not sitting in the runoff.
5. Fascia boards and roof edges
The fascia is the board along the eaves that the gutter hangs on. The USDA bulletin names sheathing and fascia boards as places where rain leaks and poor flashing cause decay, and the Solution Center points to the crevice between the roofing and the fascia, where water can do undetected damage. A drip edge, required on shingle roofs at eaves and rakes by ORSC R905.2.8.5, keeps water from curling back under the shingles onto the wood. Gutters that overflow every winter do the rest. The Handbook’s ideal is a roof overhang of about 2 feet, with gutters and downspouts kept clear.
6. Porch floors and steps
Preservation Brief 45, on historic wood porches, says the part of a porch most subject to decay is the flooring, and that decay often starts at the exposed ends of the boards. Steps and stringers are close to the ground, which the brief calls making them predictable candidates for deterioration. The USDA bulletin went further: some decay is to be expected in porch steps, floors, railings and pillars exposed to rain.
7. The base of porch columns
Wood porch columns tend to fail from the bottom up. Brief 45 says columns are prone to water seeping into open joints, particularly at the base and the lower end of the shaft. Water that gets into an open joint there has little chance to dry, and a column can look perfect from the street while its bottom foot goes soft.
8. Deck and porch ledgers
The ledger is the board bolted to the house that carries one side of a deck or porch. If water gets between it and the house, both the ledger and the house framing behind it can rot, out of sight. Brief 45 warns that a decaying ledger may compromise the structural integrity of the porch. The American Wood Council’s deck construction guide, DCA 6, requires ledgers to be flashed or caulked to keep water off the house’s band joist. Many older decks were attached with neither.
9. Garage door jambs
The side jambs of a garage door often run right down onto the concrete floor or driveway, and the bottom of each jamb sits in whatever water runs in under the door. The USDA bulletin’s advice was simple: door frames should not extend into the concrete. Look at the bottom foot of each jamb, especially on the side the driveway slopes toward.
10. Sill plates and rim joists over the crawlspace
On a house built over a crawlspace, the USDA bulletin describes moisture coming from the soil as vapor and condensing on cold sills and the outer ends of the joists, and the Handbook says condensation in crawlspaces can cause serious decay in floor framing and sheathing. Its fix is a ground cover, such as polyethylene over the soil, and at least 18 inches of clearance under the joists so someone can get in to look. Current Oregon code (R317.1) requires naturally durable or preservative-treated wood for sill plates in contact with concrete or masonry exterior foundation walls.
Rot in this spot cannot be seen from the yard. Portland Crawlspace Pros explains how to check the floor framing from below, including the screwdriver test and what to note about where the soft wood is.
Is it rot, or something else?
A few things look like rot and are not, and a couple of things point to it.
- Mildew and mold are surface growths, usually gray, green or black. They wipe or wash off, and the wood underneath is firm.
- Iron stain is a dark discoloration around nails and fasteners, caused by iron reacting with tannins in the wood. The Handbook notes it in some softwoods such as Douglas-fir, and says it comes back after cleaning unless the source of iron is dealt with. It is a stain, not decay, though rust streaks do tell you that spot has been wet.
- Fresh fungus is a sign of active decay: fan-shaped white or brown patches, strands or root-like growths under a board or on the back of trim, and sometimes mushrooms, brackets or crusts on the wood itself.
- Dampwood termites. Oregon State University’s pest page says the Pacific dampwood termite eats and nests in moist, water-damaged wood, and that treating them will not work unless the moisture source is removed and the damaged wood repaired. If you find them, you have found wet wood too.
How to check your own house
You need a small screwdriver or an awl and a dry afternoon.
- Walk the ten places above. Start low and work up. Bring binoculars for fascia and upper trim.
- Probe, don’t just look. The Handbook suggests probing several areas with a small-tipped screwdriver. The Solution Center’s rule of thumb: if you can easily press into the wood, that is a good indication of rot. Push at an angle into sills, board ends and column bases, where the soft core hides behind the paint.
- Read the paint. The USDA bulletin lists paint discoloration at joints, and siding that swells and buckles, as signs that moisture is not being controlled. Paint that keeps failing on the same few boards is a leak, not a paint problem.
- Look up from where the rot is. Rot is almost always below and to the side of where water gets in. The cause is usually one detail above it: a missing kickout, a sill with no slope, a gutter that overflows, a sprinkler aimed at the wall.
- Photograph what you find. Pictures of the soft spots and the details above them make it much easier for a contractor to give you a useful answer.
The siding inspection checklist turns this into a wall-by-wall walk you can do each year before the rains.
Dry rot when you buy or sell a house in Oregon
Rot turns up in a lot of Portland real estate deals, and Oregon has a few specific rules that shape how it comes out.
The seller’s disclosure. Under ORS 105.464, most sellers of one- to four-unit homes must give each buyer who makes a written offer a completed property disclosure statement. It does not ask “is there rot?” in so many words. It asks whether a pest and dry rot, structural or whole-house inspection has been done within the last three years; whether there are any moisture problems, areas of water penetration, mildew odors or other moisture conditions; and whether there are any other material defects a buyer should know about. The form also tells buyers they may want to hire specialists, naming pest and dry rot inspectors among them. Some sellers are exempt, including banks selling foreclosed homes, trustees and personal representatives of estates (ORS 105.470). A buyer who receives the statement has five business days to revoke the offer (ORS 105.475).
The home inspection. Oregon home inspectors are certified through the Construction Contractors Board, and their standards of practice matter here. The inspector must probe or sound structural components where deterioration is suspected, unless probing would damage a finished surface, and must report signs of abnormal or harmful water penetration. On the exterior, the inspection covers wall cladding, flashing and trim, attached decks, porches and steps, and eaves, soffits and fascia. But the same rules say the inspector is not required to report on wood-damaging organisms, and the inspection contract must state whether a wood-destroying organism inspection is included, or available for a fee. Inspections are also visual and not technically exhaustive. In other words, a clean home inspection report is not the same as a clean pest and dry rot report. Ask which one you are getting.
The CCB’s own home inspection notice adds one more point worth knowing: a buyer may not use or rely on an inspection report that was contracted by the seller.
The loan. If the buyer is using an FHA loan, HUD’s handbook names decay, excessive dampness, leakage and termites among its examples of defective conditions, and where there is evidence of infestation, the appraiser must make the appraisal subject to inspection by a qualified pest control specialist. The lender must also confirm that an existing home is free of wood-destroying insects and organisms. For VA loans, appraisers must report any apparent evidence of wood-destroying insect infestation, fungus growth or dry rot, and all damage must be repaired. Oregon is not on the VA’s list of states that require a wood-destroying insect inspection on every loan, so there it comes down to what the appraiser sees.
The insurance. According to Oregon’s Division of Financial Regulation, a typical homeowners policy does not pay for seepage, dry rot or pest damage, which the regulator treats as a maintenance issue rather than a sudden, accidental loss. Buyers should not count on a claim to pay for rot they find after closing.
What fixing it involves
Every rot repair has the same order of work, whatever the size.
- Stop the water. Flashing, a kickout, a drip edge, a regraded bed, a moved sprinkler. Otherwise the new wood rots too.
- Remove what has lost its strength. Since wood weakens well before rot shows, a contractor probes past the soft spot to find sound wood.
- Choose wood that can take it. The USDA bulletin recommended decay-resistant heartwood for the riskiest spots: sills, porches, outside steps and the lowest siding boards. Today that often means preservative-treated lumber, naturally durable species, or fiber cement or PVC trim where wood has failed before.
- Seal every cut end. The Handbook recommends flooding end grain with a water-repellent preservative and priming all faces before painting, including ends cut on site.
- Paint in the dry months, when the wood is below 20 percent and the finish can bond.
On older houses, partly decayed sills, trim and column bases can often be saved with epoxy consolidants or by splicing in new wood, which keeps original material. Historic wood siding repair covers those methods. For a repair focused on the siding itself, including how contractors tell surface rot from a rotted wall, see dry rot in siding and trim. If rot is turning up on every side of the house, get a price for siding replacement as well as the repair, and the siding cost page has sourced figures for both.
If you have found soft wood and want someone to look at it, request a siding quote and note where the soft spots are; we’ll follow up about your project. Before you hire, the guide to comparing siding quotes in Oregon covers what to check.
This page is general information, not professional advice about your specific situation. Have it assessed by a qualified professional before making decisions. Last reviewed September 28, 2026.
Start My Siding Quote
No cost and no obligation. Tell us about the house and the siding problem to get started.